2.7 x 60mm Paslode 15 Degree Dome Screwshank Stainless Steel Decking Coil Nails – Single Coil

Paslode 15-degree coil nails are available in multiple diameters and lengths. Common sizes include 2.7 x 50mm, 2.7 x 60mm, 2.7 x 65mm and 2.7 x 75mm. The 2.7 x 60mm (this product) is the most widely used size for standard 90mm hardwood and softwood decking boards. Available in hot-dipped galvanised (HDG) for standard applications, and stainless steel (SS) for coastal and exposed environments. Call 1300 888 729 or search the TFX product range for the full size and finish lineup.

Paslode nailers are calibrated for genuine Paslode nails. Third-party coil nails may not meet the exact wire gauge, coil angle or head diameter tolerances required, which can cause misfires, jams or tool damage. Always match the coil angle (15 degrees for this product) to your specific nailer model. Using non-genuine consumables may also void your Paslode tool warranty. Contact TFX on 1300 888 729 if you need help confirming compatibility for your model.

General loading sequence for a Paslode 15-degree coil nailer: (1) Disconnect the air supply or engage the safety lock. (2) Open the nail canister lid by releasing the latch. (3) Remove any remaining nails from the previous coil. (4) Place the new coil in the canister with nail heads facing the correct direction per your model manual. (5) Feed the lead nail into the nail guide at the nose of the tool. (6) Close the canister lid firmly. (7) Reconnect the air supply and test-drive a few nails into scrap timber before proceeding. Refer to your specific Paslode model manual for exact instructions, as the sequence varies between models.

Yes. Stainless steel nails are specifically designed for exterior and outdoor use, particularly in coastal, high-humidity or permanently wet environments. Unlike galvanised nails, which can corrode within 5 to 10 years in exposed conditions, 316-grade stainless steel resists rust indefinitely under normal outdoor use. They are the recommended choice under Australian building standards for decking, fencing and external cladding in coastal zones within 5km of the ocean or in areas with high annual rainfall.

For Australian timber decking, stainless steel screwshank nails are considered best practice. The screwshank profile outperforms smooth and ring shank for withdrawal resistance as boards expand and contract. For coastal or exposed environments, 316 stainless steel is essential to prevent corrosion and rust bleed staining into decking faces. Hot-dipped galvanised (HDG) nails are acceptable for low-corrosion inland areas but should not be used within 5km of the coast or in permanently wet applications. Always check your decking timber supplier specification, as some treated timbers specify fastener type and minimum corrosion class.

Yes. Both stainless steel screws and nails are used for decking. Screws provide better hold and are removable for future board replacement. Nails (particularly screwshank) are faster to install with a pneumatic nailer and less likely to cause face-splitting on hardwoods. For large commercial or production decking jobs, stainless steel coil nails are preferred for speed. For residential builds where board access may be needed in future, screws are a valid alternative. The right choice depends on your specific timber specification, project scale, and programme requirements.

Stainless steel nails outperform galvanised in three areas: corrosion resistance, longevity and appearance. In coastal, high-humidity or exposed environments, galvanised nails can corrode within 5 to 10 years, causing rust staining on timber faces and potential structural failure at the fastener. Stainless steel (316 grade) does not corrode under these conditions. While SS nails cost more upfront, eliminating callbacks, rework and rust bleed staining makes them the cost-effective choice for any external or coastal application.

Ring shank nails offer greater withdrawal resistance than smooth shank, making them a step up for decking. However, screwshank nails are generally considered superior because the helical thread cuts into timber fibres like a screw, providing even greater holding power as boards move with seasonal moisture changes. Screws provide the highest withdrawal resistance of all fastener types and are removable, but require more installation time. For production decking at scale, screwshank coil nails are the preferred trade choice, combining the speed of nailing with performance approaching that of screws.

Ring shank nails are best used where superior holding power is needed and screwshank is not available, or for sheet material applications such as flooring, plywood and OSB where the annular rings grip timber fibres to resist pull-out. For structural hardwood decking, screwshank is generally preferred because the helical profile handles greater withdrawal forces under dynamic load and seasonal board movement. Ring shank can be a cost-effective intermediate option for non-coastal inland softwood decks where HDG is acceptable.

Builders use nails for production decking and framing primarily for speed and cost-efficiency. A pneumatic coil nailer can drive 300 nails per coil in minutes. Screws require more time per fastener, even with an impact driver. For large-volume commercial and residential jobs, nails are far more cost-effective in labour terms. Structurally, nails also flex under dynamic load rather than shearing, which is advantageous in framed structures subject to wind and movement. Screws are preferred where boards must be removable or maximum withdrawal resistance per fastener is needed.

Deck screws: Pros: highest withdrawal resistance, removable for board replacement, clean countersink finish. Cons: slower to install, higher unit cost, potential for shear failure under lateral load.

Ring shank nails: Pros: fast installation with a pneumatic nailer, good withdrawal resistance, flexible under dynamic load. Cons: not removable, lower withdrawal resistance than screwshank or screws, can work loose in high-movement hardwood applications.

For most Australian hardwood coastal decks, the optimal choice is stainless steel screwshank coil nails: combining the installation speed of nailing with withdrawal performance that approaches screws, in a corrosion-resistant finish.